100 Series
900 Series
1000 Series
1300 Series
2000 Series
3000 Series
4000 Series
Marine Range
100 Series
4 to 37 kW

Type
0.45 to 2.22 litre, in-line multi cylinder, water cooled engine range.

Family Description

The 100 Series is a range of two, three and four cylinder diesel engines, fully proven in the agricultural equipment sector.  Previously Made in Japan for Perkins by ISM, the demand for 100 Series engines has been such that from 1996 they will also be produced in Peterborough by Perkins Shibaura Engines Ltd, a joint venture company within the Perkins Group.  This will enable even higher levels of customer service.

Customer benefits

  • Single sided service across the range contributes to simple maintenance and very low down time.
  • The small bore, multi cylinder, water cooled, IDI designs are exceptionally quiet and clean - industry benchmarks in their for both noise and emissions performance.
  • Each engine in the seven model range has an excellent power to weight ratio for high mobility and reduced package size.

Standard Equipment

  • Starter Motor
  • Alternator
  • Side outlet exhaust manifold
  • Bottom and side drain oil sump
  • Crankshaft front pulley with PTO facility
  • Cooling fan
  • Provision for timing case hydraulic pump
  • Fuel lift pump and filter
  • Glow plug starting system
  • Electric shut down solenoid
  • Oil pressure switch
  • water temperature switch

Options

  • Standard engine back plate
  • SAE short and long flywheel housings
  • Flatface flywheel to accept Centaflex type coupling
  • SAE light and heavy flywheels

Accessories

  • Air filtration systems
  • Radiator kits
  • Automatic engine shutdown units
  • Auxiliary hydraulic pumps and drives
  • Exhaust manifolds
  • Electric fuel lift pumps
  • Fuel pre-filters
  • Exhaust silencers
  • Engine mounting feet
  • Fast-start glow plugs
  • Extended dipsticks
  • Cassette type fuel injection system
  • Heat treated chrome molybdenum steel crankshaft
  • Plateau honed cylinder bores for superior oil control
  • Simplified timing drive using only 3 helically cut gears
  • Tunnel main bearing crankshaft support system for high strength

Clean Emissions

Highly efficient combustion is achieved through our indeirect fuel injection system, with compromised pre-combustion swirl chambers.  This same efficiency makes the 100 Series capable of exceeding all emissions standards worldwide.

Dimensions
Model A
Flywheel to Fan Face
mm (ins.)
B
Fan Centre to Crank Centre
mm (ins.)
C
Total Height
mm (ins.)
D
Crank to base of Sump
mm (ins.)
E
Overall Width
mm (ins.)
Weight (kg)
kg (lbs)
104-22 646 (25.4) 276 (10.87) 718 (28.27) 252 (9.92) 463 (18.2) 184 (405)
104-19 646 (25.4) 254 (10.0) 676 (26.6) 232 (9.13) 475 (18.7) 180 (396)
103-15 533 (20.98) 254 (10.0) 659 (25.9) 219 (8.62) 459 (18.1) 149 (328)
103-13 529 (20.82) 254 (10.0) 636 (25.0) 219 (8.62) 422 (16.61) 137 (302)
103-10 459 (18.10) 195 (7.67) 553 (21.77) 199 (7.83) 377 (14.84) 83 (183)
103-07 443 (17.44) 175 (6.89) 500 (19.69) 195 (7.68) 357 (14.05) 72 (158)
102-05 369 (14.52) 175 (6.89) 488 (19.20) 183 (7.20) 350 (13.77) 59 (130)

 
Model Gross Rating
Max. Intermittent Power Max. Torque
kW rpm Nm rpm
102-05 8.2 3,600 25.5 2,300
103-07 13.4 3,600 38.2 2,400
103-10 17.5 3,600 54.3 2,400
103-13 20.8 2,800 77.6 2,200
103-15 23.5 2,800 87.0 2,100
104-19 31.7 2,800 116 2,200
104-22 37.0 2,800 140 2,100

 
Model Swept Volume (litres) Bore Stroke (mm) Configuration/Cylinders
102-05 0.451 67x64 2 in line
103-07 0.676 67x64 3 in line
103-10 0.954 75x72 3 in line
103-13 1.33 84x80 3 in line
103-15 1.50 84x90 3 in line
104-19 2.00 84x90 4 in line
104-22 2.22 84x100 4 in line

 
Model Aspiration Flywheel Flywheel Housing
102-05 NA SAE 6.5 SAE 5
103-07 NA SAE 6.5 SAE 5
103-10 NA SAE 6.5 SAE 5
103-13 NA SAE 6.5 SAE 4
103-15 NA SAE 7.5 SAE 4
104-19 NA SAE 7.5 SAE 4
104-22 NA SAE 7.5 SAE 4